FTTH IP68 waterproof 12 port fiber optic terminal box with mini SC connectors, corning optitap compatiable
FTTX Enclosure is a new economic fiber distributed solution for outdoor use. Compare traditional products, FTTX Enclosure is easy to operate and has high compatibility. It can be used for wall-mounting, aerial installation or holding pole installation, based on different situation.FTTX Enclosure not only used in FTTH field, but also used in FTTA or other harsh environment.
1. FTTH field
Traditional solution use ONU or FDH (Optical Network Unit/Fiber Distribution Hub), when trunk optical cable arrives to outside of mansions and villas. FiberHub® can replace ONU or FDH because it has fiber distribution function. Inside, it can be fixed 2-4pcs 1 *8 or 1*16 PLC, and can be put 24pcs fiber splice protection sleeves.
After mating with 1-48F IP67 preassembled waterproof connector, FiberHub" can connect each mansion and villa or low voltage silo directly. It can be fixed outside of mansions and villas, or holding pole installation. FiberHub® can reduce signal loss through less connecting node. For in factory preassembled FiberHub®, it’s no need high skill operator because of no fiber splice operation. Installation efficiency can be increased by 40%.
Traditionally, Remote Radio Unit (RRU) and Building Base band Unit (BBU) connected by optical fiber cable, formed star network topology. Each RRU need one duplex outdoor cable link to BBU. Installation will need more time and cost will be high.
FiberHub® work as an Aggregation/Demark box, link RRU and BBU together. From BBU to FiberHub®, only need one multi-fiber hybrid cable. Then FiberHub" divide fibers to each RRU through IP67 preassembled waterproof cable assemblies. RRU can get power through assembled power connector on FiberHub®.
3.Trunk Cable Connecting
Trunk cable needs to be fusion welded frequently because of each drum cable length limited. So connecting point is weak and need to be protected very well.
When trunk cable comes into FiberHub®, it will be sealed and fixed by torsion proof cable gland (plastic or metal type). For 5mm-14mm out diameter cable, FiberHubK has different accessories to fit. Torsion gland can release stress when trunk cable bending and protect fiber avoid breaking. Inside of the FiberHub' main cable and strength member were fixed by fastener, which make sure the box can stand 1200N pulling force long term.
Splice protection sleeve (Max. 24pcs) and PLC (Max.2pcs) can be fixed on the body, which make FiberHub® fiber divided very easy. Anti-skid design on the base case, which makes sure FiberHubK holds wire/pole firmly.
4.Prospecting or Military Communication
The cable will be replayed frequently, when prospecting or military communication. Normal connector and cable cannot stand frequently and high strength pulling and reuse. Inside of the FiberHub®, armored cable and strength member were fixed by fastener, which make sure the box can stand 1200N pulling force long term. It’s very suitable for field use, especially in star network communications. High strength material and arc interface design make sure FiberHub6 work abnormally when suffer shocks.
Features and Benefits
•High compatibility: can be assembled ODVA, Hconn(OptiTap™ compatible), Mini SC, AARC, PTLC, PTMPO or
'Factory-sealed or field assembly
•Strong enough: working under 1200N pulling force long term •From 2 to 12 ports for single or multifiber harsh connectors •Available with PLC or splice sleeve for fiber divide •IP67 waterproof rating
*Wall mounting, aerial installation or holding pole installation
* Decreased angle surface and height make sure no connector interfering when operating
•Meet I EC 61753-1 standard
•Cost effective: save 40% operating time
||365x137x90mm(Without cover) 375x142x120mm(With cover)
||-40 to + 80°C
|Cable strength member
||Armoured or Non-armoured
||Hybrid or non-hybrid
|Round cable OD
||5.0mm to 14mm
|Flat cable dimension
|Cable jacket material
|Cable crush resistance
||200N/cm long term
i zuuiN long lerm
|Fire protection rating
|Number of PLC
||1 to 2pcs
|Number of fusion protection sleeve
||1 to 24pcs